Bosch · Refrigerator Moderate

E11 — Display Control Module Fault

Bosch's official US refrigeration error-code page documents only three entries: E02 (icemaker/ice-water communication), E03 (dispenser UI), and a generic 'E or D' catch-all. A bare 'E11' is not separately documented on the refrigeration page (note: E11 does have an official but different meaning on Bosch dishwashers/ovens — touch-key/condensation — do not assume that carries over to refrigerators). The 'display control module fault' explanation below is not confirmed — verify against your model's manual, or treat it per Bosch's generic guidance: power-cycle, and call support if it persists.

Keep using it?
Yes, with caution
DIY difficulty
Moderate

How to fix it

  1. Unplug the unit.
  2. Remove the rear lower access panel.
  3. Vacuum dust and pet hair from the condenser coils and fan blade.
  4. Spin the fan by hand; replace if stiff or noisy.
  5. Test the harness for continuity and proper voltage on the next start-up.
  6. Replace the condenser fan motor if dead; replace the main board if the motor and wiring are good.

Why it happens

Typical signs: E11 displayed · Compressor area very hot · Unit cycles off and on · Reduced cooling capacity

  • Failed condenser fan motor DC motor with internal failure.
  • Debris jamming the fan Pet hair, dust, or paper on the blade or shroud.
  • Disconnected harness Fan connector backed out during cleaning or service.
  • Main control board output failure Board cannot drive the fan.

Replace your water filter

A clogged or overdue water filter is a common cause of low water and ice flow on Bosch refrigerators — they are meant to be changed about every 6 months. The OEM-style filter that fits most Bosch refrigerators is the BORPLFTR10 ($60-75 OEM, $25-35 compatible).

  • Bosch BORPLFTR10 refrigerator water filter OEM water filter
    Amazon →

Not sure which filter fits your model? See the full compatibility guide →

Parts you may need

If diagnosis points to a failed part, these are the common replacements. As an Amazon Associate we earn from qualifying purchases.

  • Bosch refrigerator display control module Common replacement
    Amazon →

More Bosch refrigerator codes

E1 E1 — Fresh-Food Compartment Sensor Fault E10 E10 — Inverter Compressor / Compressor Drive Fault E12 E12 — Damper Control Fault E2 E2 — Icemaker / Ice-Water System Communication Fault E20 E20 — Defrost Drain Heater / Drain Blockage E3 E3 — Dispenser User Interface Fault

All Bosch codes → All refrigerator codes →

Frequently asked questions

What does the E11 code mean on a Bosch refrigerator?

Bosch's official US refrigeration error-code page documents only three entries: E02 (icemaker/ice-water communication), E03 (dispenser UI), and a generic 'E or D' catch-all. A bare 'E11' is not separately documented on the refrigeration page (note: E11 does have an official but different meaning on Bosch dishwashers/ovens — touch-key/condensation — do not assume that carries over to refrigerators). The 'display control module fault' explanation below is not confirmed — verify against your model's manual, or treat it per Bosch's generic guidance: power-cycle, and call support if it persists.

What causes the E11 code on a Bosch refrigerator?

Failed condenser fan motor: DC motor with internal failure. Debris jamming the fan: Pet hair, dust, or paper on the blade or shroud. Disconnected harness: Fan connector backed out during cleaning or service.

Is it safe to keep using a Bosch refrigerator with a E11 error?

Yes, with caution. This is rated a moderate-severity fault.

How do I fix E11 on a Bosch refrigerator?

Unplug the unit. Remove the rear lower access panel. Vacuum dust and pet hair from the condenser coils and fan blade.

Always unplug an appliance before servicing it. This guide is for informational purposes and is not a substitute for a qualified technician.