GE Error Codes
102 GE codes. Jump to your appliance:
GE Dishwasher Codes18
- 1h 1h — Delay Start Active
- 888 888 — Display Self-Test / Demo
- C1 C1 Error — Slow Drain (Over 2 Minutes)
- C2 C2 Error — Drain Cycle Too Long (Over 7 Minutes)
- C4 C4 — Overfill / Filled Twice After Power Loss
- C5 C5 — Underfill / Short Drain Time
- C7 C7 — Water Temperature Sensor (Thermistor) Fault
- C8 C8 — Detergent Dispenser Fault
- Control Lock Control Lock — Buttons Locked Out
- DR DR — Door Latch / Door Open Fault
- End / Clean (blinking) Clean Light Blinking — Stored Fault Code
- FILL FILL — Fill Time Exceeded
- H2O H2O Error — Low Water / Not Filling
- LEAK Leak Detected — Cycle Cancelled
- LOC LOC — Likely Control Lock
- PF PF — Power Failure
- Sanitized LED Off Sanitized Light Off / Not Sanitized
- SR SR — Undocumented (Stuck Relay is C1)
GE Dryer Codes14
- AF AF — Air Flow restriction
- E1 E1 — Inlet thermistor open circuit
- E1F E1F — Door lock / door switch failure
- E2 E2 — Inlet thermistor shorted
- E2F E2F — Exhaust air thermistor failure
- E3 E3 — Outlet (exhaust) thermistor open
- E4 E4 — Outlet thermistor shorted
- E5 E5 — Exhaust thermistor circuit fault
- E8 E8 — Drive motor / power supply fault
- E80 E80 — Control board internal communication fault
- F01 F01 — Main control board communication error
- L2 L2 — Power supply / 240V issue (L2 missing or swapped with neutral)
- PF PF — Power Failure during cycle
- tE3 tE3 — Drum/cabinet thermistor over-temperature
GE Microwave Codes16
- DOOR DOOR — Door not fully closed / open too long
- F0 F0 — Communication / no key entry fault
- F1 F1 — Open Thermal Sensor (Overheating)
- F10 F10 — Shorted Touch Screen
- F11 F11 — Shorted Touchpad / Keypad
- F2 F2 — Shorted Thermal Sensor
- F3 F3 — Shorted Touch Pad
- F3 -E0 F3 — Shorted Touch Panel
- F4 F4 — Open Humidity Sensor
- F5 F5 — Shorted Humidity Sensor
- F6 F6 — Shorted Temperature Probe
- F7 F7 — Stuck key on function keypad
- F8 F8 — Damper / vent motor fault
- F9 F9 — Door switch / monitor switch fault
- LOC LOC — Control lock active
- PF PF — Power failure indicator
GE Oven Codes22
- dF dF — Door Latch Switch Fault
- F0 Range/Oven F0 — Keypanel Problem
- F1 F1 — Keypanel (Touchpad) Problem
- F2 F2 — Oven Over-Temperature
- F3 F3 / F4 — Oven Sensor Needs Replacement
- F30 F30 — Oven Temperature Sensor Circuit Open
- F31 F31 — Oven Temperature Sensor (RTD) Open
- F350 Range/Oven F350 — Cooling Fan Circuit / Obstruction
- F4 Range/Oven F4 — Oven Sensor Needs Replacement
- F5 Range/Oven F5 — Electronic Control Needs Replacement
- F6 F6 — Keypad or Door-Lock Fault (Model-Dependent)
- F7 F7 — Stuck or Shorted Button
- F8 Range/Oven F8 — Electronic Control Needs Replacement
- F9 F9 Error — Door Lock Circuit Fault
- F90 F90 — Lock Motor Not De-Energizing
- F91 F91 — Lock Motor Direction / Drive Fault
- F96 F96 — Convection Fan Feedback Failure
- F97 F97 — Cooling Fan Fault
- FC Range/Oven FC — Door Lock Circuit Failure
- FD Range/Oven FD — Probe or Receptacle Issue
- FF Range/Oven FF — Electronic Control Needs Replacement
- LOC LOC — Control Lock Active
GE Refrigerator Codes15
- AF — Replace Air Filter Reminder
- CC CC — Fresh-food temperature out of range
- CI CI — Check Ice Maker
- dE dE — Defrost system fault
- dF dF — Defrost cycle failure
- E1 E1 — Not in GE's Official Fault-Code List
- E2 E2 — Not in GE's Official Fault-Code List
- Er Co Er Co — Communication error between control boards
- Er FF Er FF — Freezer Evaporator Fan Failure
- Er IF Er IF — Icemaker fan circuit fault (Profile / French-door)
- FF FF — Freezer Temperature Too High
- PF PF — Power Failure
- Sb Sb — Sabbath mode active
- tC tC — TurboCool active (not a fault)
- tF tF — TurboFreeze active (not a fault)
GE Washer Codes17
- dF / dE dF / dE — Door Lock Engagement Error
- E22 E22 — Drain Pump / Drain Time Exceeded
- E23 Drain Pump Error — Will Not Drain
- E31 E31 — Pressure Sensor Fault
- E42 E42 — Door Lock Will Not Unlock
- E43 E43 — Door Open During Cycle
- E54 E54 — Motor Control / Drive Motor Fault
- E57 E57 — High Current on Inverter
- E76 E76 — Heater Circuit Fault
- FILL FILL — Slow or No Fill
- FL FL — Flood / Leak Detected
- H2O H2O — No water detected entering tub
- LID LID — Lid Lock / Lid Switch Fault (Top Load)
- OL OL — Overload / Off Balance
- Sud / SUDS Sud / SUDS — Excess Suds Detected
- tE tE — Temperature Sensor Fault
- UB UB — Unbalanced Load